Go Back   RCLargeScale.com > Regional > Southeast > Georgia

Notices

Loading

Thread: Noob setup help

Reply
 
LinkBack Thread Tools Display Modes
Old 02-21-2016, 08:10 PM   #1
Newbie
 
Join Date: Feb 2016
Location: Atlanta
Posts: 3
Default Noob setup help

I'm new to the 1/5 scale RCs and have a XCR-1000 setup but, would like someone who has been in the hobby a while to go over my tx setup end points and server. I'm in the College Park area of GA. If anyone is close and willing to assist, please let me know.

Any help will be greatly appreciated.
setay is offline   Reply With Quote
Sponsored Links
Old 02-22-2016, 03:12 AM   #2
Addict
 
Join Date: Feb 2012
Location: Huntington
Posts: 314
Default Noob setup help

It's not that hard just set car up on block
And make sure the servo is centered and the wheels are pointed straight and turn wheel full left and adjust till it hits the steering stop one point at a time on transmitter now the same to the right
And do the same thing for the throttle
Only take a finger and push on the kidney that the linkage hooks to at carb
You can feel it hit the stop at wide open hold it there
And just adjust servo throw till it touches the bead on the servo arm
Now for the hard one the brakes
On most cars it won't be a large amount of travel
I adjust them till the car won't roll or I can't push it with them on
Now don't hold them on its on stop and off so the servo doesn't get hot
That's it it's not hard and just take your time after all seams right start car and have it up against a wall to help stop it if you did something wrong like servo got reversed after you turned radio off and didn't save the settings

Last edited by Nitrocat; 02-22-2016 at 03:30 AM.
Nitrocat is offline   Reply With Quote
Old 02-27-2016, 05:16 PM   #3
Newbie
 
Join Date: Feb 2016
Location: Atlanta
Posts: 3
Default Re: Noob setup help

Thanks my friend. I did some research and looked at some videos on youtube. The directions I went by for my setup is exactly what you said. There was a great series on the Losi 5ive setup by team fast eddy. The short story, I did get her setup. It still needs some adjustments but, I did get a tank and a half in today. Slow going but, fun after a killer week.

One question you may be able to answer. When I do turn the steering and the wheels center back there is a hum for the servo at neutral. If I lift the fron slight off the ground it stops. Can this be correct with the servo saver or should I go back and may more adjustments in the trim/subtrim?

Once again, thanks for the reply Nitrocat!
setay is offline   Reply With Quote
Reply


Noob setup help - Similar Threads
Thread Thread Starter Forum Replies Last Post
noob slent29 Introduce yourself 1 03-01-2015 04:31 PM
noob from cali tapout24 Introduce yourself 8 07-30-2012 10:42 AM
Noob with a 5T ScottyRock Introduce yourself 1 03-09-2012 03:07 AM
Noob OneHump Introduce yourself 11 01-29-2009 09:14 PM
Im a noob rcnoob Introduce yourself 4 06-12-2008 06:50 PM
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 11:36 PM.


Powered by vBulletin® Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Garage Plus, Vendor Tools vBulletin Plugins by Drive Thru Online, Inc.